Menu

LT & HT Power Cables for Distribution, Industry and Utilities

Power cables carry electricity from source to load, so they must be safe, durable and correctly sized. Stuffind supplies low tension (LT) and high tension (HT) power cables in copper and aluminium, with fast delivery across Pakistan and help choosing the right cable for your project.

[Request a Quote] [Contact Our Team]


What Are LT and HT Power Cables?

LT (low tension) cables carry low voltages, typically up to 1 kV. HT (high tension) cables carry higher voltages, typically from 3.3 kV up to 33 kV and beyond. Because the voltage levels differ, the construction differs too. HT cables need thicker insulation and extra screening so that the electric field stays under control.

Both types have the same basic parts. A conductor carries the current, insulation keeps it contained, and an outer sheath protects the cable. However, armoured versions add a layer of steel wire or tape, which protects the cable from impact, crushing and digging damage. As a result, armoured cables suit underground and outdoor installations where plain cable would not survive.

LT vs HT at a Glance

LT Cable HT Cable
Typical voltage Up to 1 kV (e.g. 0.6/1 kV) 3.3 kV, 6.6 kV, 11 kV, 33 kV
Typical use Buildings, factories, final distribution Substations, plant feeders, utility networks
Insulation thickness Thinner Thicker, with conductor and insulation screens
Common insulation PVC or XLPE XLPE (most common)
Cost Lower Higher

Types of LT and HT Power Cables

Several constructions are available, so you can match the cable to the installation.

PVC Insulated LT Cables

These are economical, flexible and widely used for building and light industrial distribution. They suit conductor temperatures up to about 70°C.

XLPE Insulated LT and HT Cables

Cross-linked polyethylene (XLPE) insulation handles higher temperatures, typically up to 90°C in continuous operation. Consequently, XLPE cables carry more current than PVC cables of the same size, and they are the standard choice for HT cables.

Armoured Cables (SWA / STA)

Steel wire armour (SWA) or steel tape armour (STA) gives mechanical protection. In addition, the armour can serve as an earth path where the design allows it. Therefore, armoured cable is the usual choice for direct burial, trenches and outdoor routes.

Unarmoured Cables

These are lighter and easier to install, so they suit conduits, ducts and indoor trays where mechanical damage is unlikely.

Copper and Aluminium Conductors

Copper offers higher conductivity and easier termination. Aluminium, on the other hand, is lighter and more economical for large feeders, but it needs larger sizes and careful jointing.

Single Core and Multi-Core

Multi-core cables (2, 3, 3.5 or 4 core) simplify installation. Meanwhile, single core cables suit large currents and long HT runs.


Typical Specifications

(Confirm these values against your actual product range before publishing.)

Specification Typical Details
Voltage grades LT: 0.6/1 kV. HT: 3.8/6.6, 6.35/11, 19/33 kV (confirm per product)
Conductor Copper or aluminium, stranded (circular or shaped)
Insulation PVC or XLPE
Cores 1, 2, 3, 3.5 or 4
Armour Unarmoured, SWA, STA or aluminium wire (single core)
Outer sheath PVC (flame-retardant options available)
Size range 1.5 mm² to 630 mm² (confirm per product)
Max. conductor temperature PVC: 70°C. XLPE: 90°C
Standards IEC 60502-1 (LT), IEC 60502-2 (HT), BS 5467, BS 6346 or equivalent (confirm per product)
Supply form Wooden or steel drums

Key Features & Benefits

LT and HT power cables deliver safe, stable power over long distances. Because XLPE insulation tolerates heat, it allows higher current ratings and better short-circuit performance. Moreover, it resists moisture and ages slowly, so the cable lasts for decades when installed correctly.

Armoured options add mechanical strength, which is vital for buried and outdoor routes. In addition, PVC outer sheaths resist abrasion, chemicals and moisture. For safety-critical sites, flame-retardant and low-smoke versions are also available.

Finally, a wide range of sizes and voltage grades means one supplier can cover your whole project, from a small distribution board to a plant substation.


Applications

LT and HT cables serve any site that distributes electrical power. For example:

  • Utilities and substations: incoming and outgoing feeders
  • Industrial plants: motors, transformers and process equipment
  • Commercial buildings: risers, main distribution and plant rooms
  • Construction projects: temporary and permanent supply
  • Solar and renewable plants: AC collection and grid connection
  • Fuel stations and depots: supply from transformer to switchboard
  • Water and wastewater plants: pumping stations and treatment works
  • Housing schemes and infrastructure: underground distribution networks

How to Choose the Right Power Cable

First, determine the voltage level. LT cable is enough for most buildings and factories. However, if you connect to an 11 kV or 33 kV network, you need HT cable with the proper screening.

Next, calculate the current load. Then choose a conductor size that carries it safely, because an undersized cable overheats and wastes energy. In addition, check the voltage drop over the cable length, since long runs usually need larger sizes.

Then consider the installation method. Cable buried in the ground, in ducts or on trays carries different currents, so derating factors apply. Likewise, high ground temperature or grouped cables reduce capacity.

After that, choose the insulation and armour. XLPE gives higher ratings, while armour protects buried or exposed cable. Finally, decide between copper and aluminium, and confirm that the cable meets the standard your project requires.

Not sure which cable you need? Send us your voltage, load, route length and installation method, and we will recommend suitable options.


Installation & Safety Tips

Careful handling protects both the cable and the people who work with it. First, respect the minimum bending radius, because tight bends damage insulation and armour. Second, avoid pulling the cable with excessive force, and use rollers on long runs.

Also, keep drum ends sealed until termination so that moisture cannot enter. When burying cable, lay it at the correct depth on a bed of sand, and add warning tape above it. In addition, use proper glands, lugs and joints rated for the cable type, and test the insulation before energising.

Finally, always have qualified engineers design, install and test power cable systems, and follow local electrical regulations.


Why Buy LT & HT Power Cables from Stuffind

Stuffind is an engineering and procurement partner that supplies reliable equipment to customers across industries. Because we source from trusted manufacturers, you get consistent quality from one supplier.

We offer both LT and HT options, and we deliver across Pakistan, including Karachi, Lahore and Islamabad (adjust to where you deliver). If you need help with sizing or specifications, our team will guide you. In addition, we provide competitive quotes for full drums, cut lengths and project orders.

You can also source switchboard cables, switchgear and DBs, UPS systems and batteries from us, so purchasing stays simple.


Frequently Asked Questions

What is the difference between LT and HT cable?

LT cables carry low voltages, typically up to 1 kV, while HT cables carry higher voltages such as 11 kV or 33 kV. As a result, HT cables have thicker insulation and extra screening.

What does XLPE mean?

XLPE stands for cross-linked polyethylene. It is an insulation material that withstands higher temperatures than PVC, so XLPE cables carry more current for the same size.

Should I choose XLPE or PVC insulation?

PVC is economical and suits many building and light industrial uses. However, XLPE offers higher current ratings and better heat resistance, so it is the better choice for heavier loads and for all HT cables.

What is the difference between SWA and STA cable?

SWA has steel wire armour, which gives strong mechanical protection and high pull strength. STA has steel tape armour, which is lighter and suits less demanding routes. For direct burial, SWA is usually preferred.

When do I need armoured cable?

Use armoured cable for direct burial, outdoor routes, trenches and any location where impact or crushing is possible. In contrast, unarmoured cable works well in conduits, ducts and indoor trays.

Is copper or aluminium better for power cable?

Copper carries more current for its size and terminates easily. Aluminium is lighter and cheaper, so it suits large feeders, but it needs larger sizes and careful jointing.

How do I choose the right cable size?

Cable size depends on current load, voltage drop, installation method, ground temperature and short-circuit rating. Therefore, share these details and we will help you select the right size. A qualified engineer should confirm the final selection.

Can LT cable be used for HT applications?

No. HT applications need cables designed and tested for the higher voltage, with correct insulation thickness and screening. Using LT cable at HT voltage is dangerous.

What standards do your cables meet?

Power cables typically follow IEC 60502 or BS standards. Tell us your project requirements, and we will confirm suitable products and test documents.

How are power cables supplied?

They are supplied on wooden or steel drums, and cut lengths may be available. Contact us with your required length.

Do you supply in bulk?

Yes. We supply cut lengths, full drums and complete project orders.


Related Products

Single Core PVC Cables · Multi-Core Flat Cable · Switchboard Cables · Flexible & Control Cables · Solar & Specialized Engineering Lines · Transmission Line Conductors · All Cables


Get a Quote on LT & HT Power Cables

Tell us the voltage grade, conductor material, size, number of cores, armour type and length. Our team will respond quickly with the right recommendation and a competitive quote.

[Request a Quote]
Email: stuffind@stuffind.com
Availability: Mon–Sat, 09:00–22:00